Installing A Bath tub
Installing A Bath tub
Blog Article
What're your opinions about How to Install a Bathtub Yourself?
Installing a bath tub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily easily accessible, the task can move immediately; if you have to open a wall surface to remove the old tub as well as place the new tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. See to it you have qualified on your own for the work and are comfortable trying it. As opposed to hiring a professional to take over a halfway-completed task, it is far better to consider utilizing one prior to you start. Chances are you may need an expert plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your washroom if you have already purchased a brand-new bathtub and also do not require to change the arrangement of your previous supply of water pipelines.
Your devices and also product list should comprise the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you ought to do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of eliminating the existing taps can be rather troublesome because of the restricted gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type should be attached to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Making use of the two wood boards under its feet, put the bath tub in the needed placement. The wooden boards are helpful in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the bath tub until the level reviews level.
To mount taps, fit all-time low of the outermost flexible faucet connector to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Switch on the supply of water and also check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bath tub should wait until the tub has actually been made use of at least once as this will certainly resolve it right into its final setting.
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the adaptable faucet adapters to the bottom of both faucets using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final setting.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to break a stiff seal, causing the water to penetrate the wall between the bathroom and also the tiling, bring about difficulties with wetness as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to always load the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can split relatively early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently readily available on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that post about A Step-by-Step Guide to Installing a Bathtub while doing a lookup on the internet. Are you aware of someone else who is truly interested in A Step-by-Step Guide to Installing a Bathtub? Do not hesitate to share it. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Check Us Out
Report this page